Blog · November 15, 2026 · 8 minute read

Cork Insulation: A Deep Dive into the Pros and Cons

Cork insulation is a thermal plaster: cork and natural lime blended with porous minerals (expanded silica, perlite and pumice in Thermactive; clay and diatomaceous earth in Evolution) and applied as a continuous, breathable coat. Once set, the plaster has a porosity of about 71%. That porous structure traps air, and with the cork itself it insulates against the cold in winter and the heat in summer, while water vapour still passes through and the plaster carries a Class A1 fire rating. Its insulation builds with thickness, so the R-value comes from how many centimetres are applied, up to 4 cm a layer. Once the last layer is on, the plaster dries for 10 to 15 days, and it is applied between +5°C and +30°C.

Ses Clotades, a white rendered house among pine and olive trees in Formentera, Spain
Ses Clotades, Formentera, Spain, by architect Marià Castelló: the envelope insulated with Diathonite Thermactive, finished with an Argatherm levelling coat. Photo: Diasen.

What is cork insulation?

Diathonite is Diasen’s line of cork-based mortars: Thermactive and Evolution for insulating walls, Deumix⁺ for damp and salt-laden masonry, Sismactive for seismic reinforcement of masonry, Acoustix⁺ for sound absorption, and the Thermostep.047 and Thermostep.060 screeds for floors. Each has a thermal conductivity of its own; this post covers the two for insulating walls. Both are supplied as a premixed dry mortar in paper bags, mixed with water on site and applied by plastering machine or by hand trowel to interior and exterior walls, from a minimum of 1.5 cm and up to 4 cm per layer:

  1. Diathonite Thermactive: granulated recycled cork (0 to 3 mm), expanded amorphous silica, perlite and pumice, bound with NHL 5 natural hydraulic lime. Thermal conductivity λ 0.035 W/mK.
  2. Diathonite Evolution: granulated recycled cork (0 to 3 mm), clay and diatomaceous earth, bound with NHL 3.5 natural hydraulic lime. Thermal conductivity λ 0.045 W/mK.

What are the pros of cork insulation?

It insulates in winter and summer

Thermactive has a thermal resistance of 0.285 m²K/W per centimetre, about R-4.1 per inch. Diathonite Evolution has 0.222 m²K/W per centimetre, about R-3.2 per inch. Beside the other vapour-open materials used to insulate walls from the inside:

Vapour-open interior insulation R per inch
Mineral wool board about R-4.2
Diathonite Thermactive about R-4.1
Wood fibre insulation board about R-3.6
Cork insulation board about R-3.6
Diathonite Evolution about R-3.2

Thermal resistance only, for materials sold in Canada, from each maker’s declared values: ROCKWOOL Comfortboard 80, Gutex Thermowall 5in1, CorkTherm insulation cork board; plaster values from Diasen’s data sheets.

On a −20°C day, the inside face of a bare brick wall (230 mm, the room at 21°C) sits near 5°C, below the dew point of the room air; 25 mm of Thermactive brings it to about 16°C, and with it goes the chill you feel standing next to the wall. In summer, the same layer slows the heat coming in: Diasen gives both a thermal lag (phase shift) of up to 12 hours, depending on the wall assembly, the delay before the day’s outdoor temperature swings reach the interior.

It lets the wall breathe

Both plasters are highly vapour-permeable: Thermactive has a water vapour resistance factor (µ) of 3 and Evolution 4. Diasen formulates them to dehumidify walls and to reduce thermal bridges and humidity-related mould, and Diasen rates both ideal for historical restoration. Lime-based plasters like Diathonite also help even out daily humidity swings indoors, which research links to how comfortable a room feels; the finish over them needs to stay breathable for that to work. Research also classes cork-lime insulating plasters with calcium silicate and dense wood fibre as capillary-active: besides letting vapour through, they move liquid moisture away from the cold face of the wall so it can dry.

It’s classed A1 for fire

Both plasters are classified A1 for reaction to fire under EN 13501-1. Thermactive was also tested to ASTM E84 in 2015, with a flame spread index of 0 and a smoke developed index of 10.

It’s made of cork, lime and mineral aggregates

Recycled cork, natural hydraulic lime and mineral aggregates, with 0% VOC. At the end of its service life the plaster can be recycled as an inert material.

It follows irregular walls, old and new

As a plaster, it can be applied to flat or curved surfaces, on walls and ceilings, and directly to rough concrete, block, brick and rough plaster. Diasen describes it as ideal for historical restoration, states that it preserves the masonry over time, and intends the product line for residential, commercial and historical buildings. Smooth, painted and wood surfaces need additional preparation first; each product page gives the steps.

What are the cons of cork insulation?

A high R-value takes a thick wall, built in layers

Thermactive gives about R-4.1 per inch and Evolution about R-3.2, so a higher R-value means a thicker wall. Both plasters are applied at a minimum of 1.5 cm: RSI 0.43 (about R-2.4) for Thermactive and RSI 0.33 (about R-1.9) for Evolution. Each layer can be applied up to a max of 4 cm, which gives RSI 1.14 (about R-6.5) and RSI 0.89 (about R-5.0). Greater thickness is built up in successive layers 12 to 24 hours apart. Past 6 cm, Thermactive and Evolution require Polites 140 mesh at about mid-thickness. 

Diathonite can also be the levelling coat for a vapour-open insulation board. Apply to level out irregular surfaces then a wood fibre or cork insulation board is bonded to that flat surface, and a lime plaster finishes the board. 

It takes time and warm weather

Application requires air and substrate temperatures between +5°C and +30°C, relative humidity of 70% or less, and no rain, frost or heavy fog forecast. Once the last layer is on, the plaster dries for 10 to 15 days at 23°C and 50% RH, and longer at greater thickness. During curing, protect it from frost, direct sun and wind; in hot conditions, dampen it 2 to 3 times a day for the first 2 to 3 days. On exteriors, the skim coat follows only once the plaster has fully cured, and the finish no sooner than 7 days after the skim coat.

It works as a system of layers

  1. Aquabond, where the substrate requires it.
  2. Thermactive or Evolution.
  3. For a smooth face, an Argatherm skim coat in two passes, with Polites 80 mesh embedded between them. Left out, the plaster keeps its rougher texture under Limepaint, Plasterpaint or Decork Facade; Decork Mediterraneo and Acrilid Protect Coating need the skim coat.
  4. D20 fixative, which evens out absorption.
  5. The finish: Limepaint indoors, or Plasterpaint, Decork Facade, Decork Mediterraneo or Acrilid Protect Coating indoors or out.

What does it cost?

A 15 kg bag of Thermactive is $283.50 and covers about 41 ft² (3.85 m²) at the 1.5 cm minimum; an 18 kg bag of Diathonite Evolution is $275.20 and covers about 35 ft² (3.24 m²). The thickness calculator on each product page gives the bag count for your wall. The plaster is the insulation and the base for the finish in one, applied straight to the wall. Against a bare brick wall, 25 mm of Thermactive saves about $0.64 per square foot each heating season in Regina.

A 15 kg bag of Diathonite Thermactive poured into a mixing bucket
A bag of Diathonite Thermactive going into the mixing bucket.

What’s on file for a specification?

  1. CE marking: both plasters are double CE marked, to EN 998-1 as a rendering and plastering mortar and to EN 998-2 as a masonry mortar.
  2. EPD: the Diathonite line declaration, EPD-IES-0030959:002 on the International EPD System, covers both. It is cradle to gate (A1 to A3) to EN 15804+A2, verified by an independent third party and valid to June 17, 2031.
  3. Indoor air: a sample of the Diathonite line passed Eurofins testing for French VOC class A+, Blue Angel DE-UZ 113, CDPH Standard Method v1.2 and BREEAM Exemplary Level, with a LEED v4.1 low-emitting materials attestation.
  4. Fire: Class A1 to EN 13501-1 for both plasters; ASTM E84 flame spread 0 and smoke developed 10 for Thermactive. Decork Facade is classed B-s1,d0 to EN 13501-1 as a 2 mm finish on A1 or A2 substrates.
  5. Documents: the technical data sheet, safety data sheet and certificates are on each product page.

Which one fits the project?

Both insulate masonry, interior or exterior, where the wall must stay vapour-permeable.

  1. Thermactive: the higher thermal resistance per centimetre and the lower density.
  2. Evolution: the lower water absorption (0.40 against 1.00 kg/m²·min⁰·⁵) and the higher flexural strength.
Painted concrete block walls coated green with Aquabond, with grey Diathonite Thermactive applied across the middle wall
Painted block in our Regina showroom: Aquabond first, then Diathonite Thermactive applied over it.
Two walls fully covered in freshly applied Diathonite Thermactive, still wet and darker grey
The finished coat, still wet; it dries lighter.

See Diathonite in person at 608 4th Avenue East. Not in Regina? Call us at 1-866-326-8321 or visit ecotechnology.ca to explore what’s possible.

Take an idea further

Ask Atlas anything about Diathonite Thermactive, or go straight to the product.