Blog · June 30, 2025 · 4 minute read
Five Mistakes to Avoid When Installing Microcement in a Shower
Microcement showers are stunning, seamless and spa-worthy, and they demand attention to detail. Whether you're a first-time DIYer or a contractor trying Eco-Tech's kit for the first time, this guide will help you sidestep the most common missteps. Because fixing mistakes after the fact is far more costly than avoiding them in the first place.
1. Skipping Surface Preparation
Surface prep is foundational. If you apply microcement over dusty, glossy or poorly bonded substrates, your beautiful finish can fail. This is especially crucial in areas exposed to water like shower and tub surrounds.
What to do instead:
- Lightly sand glazed tile with 80-grit sandpaper to dull the shine. Tile is the only surface that gets sanded.
- Clean thoroughly using a degreaser like TSP.
- Remove all silicone and caulk so the WATstop can bond.
- Make sure all surfaces are dry and free from movement.
- Repair cracks and fill grout lines deeper than 3 mm with Ardex X5.
- Roll on two coats of WATstop: 1 kg/m² in all over tile, cement board or moisture-resistant drywall, 2 kg/m² over concrete. WATstop is the waterproof layer, so no separate primer goes under it. Kerdi Board is already waterproof and takes one coat of Grip Primer instead.
- Embed Safety Joint Roll in the WATstop at every inside and outside corner and where the wall meets the floor. Joints that move get Diaseal Strong first, with the Roll bridged over it.
Pro tip: Every layer above depends on the prep underneath, so give it the most time.
2. Mixing Too Much at Once
Every product in a shower system has a working time once mixed. Decorkrete starts to stiffen at about 30 minutes; keep remixing with the paddle and you have about 60 minutes of work time at 20°C or cooler. WATstop and Aquafloor Eco give you 2 hours.
What to do instead:
- Start with small batches (just what you can apply in the working time of the product).
- Use a scale for precision if working in partial amounts.
- Remix gently if the mix starts to stiffen. Don’t add water.
- Be mindful of your experience level. You will work faster as you learn.
Pro tip: Microcement behaves more like fresh plaster than paint. It’s better to mix twice than waste a batch.

3. Rushing Between Coats
Not allowing layers to cure properly can compromise adhesion.
What to do instead:
- Apply Decorkrete 24–48 hours after the last WATstop coat. Past 48 hours, the WATstop needs sanding and a coat of Grip Primer first.
- Wait 4–6 hours between Decorkrete coats, and 24 hours after the second coat before sanding.
- After sanding and cleaning, roll on one coat of D20 and give it 3 hours before the sealer.
- Let Aquafloor Eco dry 1–2 hours between its three coats. It’s walkable after 24 hours; keep water off the shower for 5–7 days after the last coat.
Pro tip: Good things take time, especially with water-based or cementitious layers.
4. Sealing Over Sanding Dust
Sanding leaves fine dust in the microcement’s texture. Left there, it keeps the sealer from bonding, and Aquafloor Eco can fail or show roller marks.
What to do instead:
- Sand once, 24 hours after the second Decorkrete coat, with 80–120 grit (120 grit by hand on edges). Between coats, sand only ridges you didn’t want.
- Vacuum, wipe with a well-wrung damp cloth and let it dry 30–60 minutes before the D20.
Pro tip: D20 binds the last traces of dust that cleaning can’t reach. It doesn’t replace the cleaning.
5. Expecting Perfection
Many first-timers freeze up trying to achieve a flawless finish. But microcement is an artisanal material; its beauty lies in variation.
What to do instead:
- Embrace irregularities; they add texture and uniqueness.
- Practice on a test board first.
- Use short, random trowel strokes. Don’t overwork it.
- Lap marks and dark streaks can be sanded back and recoated.
Pro tip: Stop working a spot once it starts to stiffen. Going back over it then leaves dark streaks.
Final Thought
Mistakes with microcement are fixable, and preventable is better. By prepping properly, mixing smart, respecting drying times, cleaning before you seal and embracing the material’s character, you’ll get a durable and beautiful shower finish.
Need guidance on your project? Reach out anytime. We’re here to help you build it right, the first time.
Related Links:
Take an idea further
Ask Atlas anything about Decorkrete Mineral Microcement, or go straight to the product.